Specifically, what steps need to be taken to reduce pressure from fuel system?How do you change the fuel filter on a 2002 Ford Explorer?Yours is a nightmare and needs to be done preferably by a experienced person.
If you still want to tackle it, you can either disconnect the fuse/relay that powers the fuel pump and start the vehicle till it runs out of gas, or on almost all of them, their is a schrader valve (like a tire valve) on the fuel rail under the plastic cover on top of the motor.. it uses two torx fasteners near the oil filler cap
take the cover off the schrader and depress the valve till all fuel is gone.
Jack up and put jack stands under the vehicle on right side, the fuel filter is under a cover, just behind the right exhaust the cover has two bolts that hold it up (there may be a few more covering some covers) but the fuel filter has two clips that use a fuel line tool (available at the national chain stores like autozone and Napa)to remove.
it pulls out of it's holder.and just reassemble and cycle the key on and off a couple of times to inspect for leaks then start and recheck for leaks.
But IMO, this fuel filter and the one on my old f-150 are the worst ones and is worth paying a professional mechanic for the heartacheHow do you change the fuel filter on a 2002 Ford Explorer?Follow the fuel line to the filter. Mine was on the driver side under the door frame and I had to unbolt it from chasis. It had some-kind-of nipple interlock that freed by pushing or pulling.How do you change the fuel filter on a 2002 Ford Explorer?first you need to get a specalty tool that fits into the connector where the fuel lines fit into the filter just put the tool around the line push it towards the filter while pulling on the line it should pop right off but it is a bear....good luck
Wednesday, September 14, 2011
How do you remove the fuel filter from a mazda b4000 pickup?
I have undone the little clips on either side and popped the filter out of its holder, now all thats needed are to pull the hoses out of either end, but how the hell do they come out? Ive tried pulling and prying with a little prybar-yet no progress-How do you remove the fuel filter from a mazda b4000 pickup?go buy a chilton book and it will tell u how to do it step by stepHow do you remove the fuel filter from a mazda b4000 pickup?there is a special tool you need, it looks like a round piece of plastic that you can pick up from an auto parts store, its like a 10cent piece of plastic but they usually come in sets of different sizes for about $14. put it around the fitting and press inwards and it should release. email me with your address and I'll send you a pic of what it looks like
How do I remove a stuck bolt on my fuel filter?
I soaked it in WD-40 and it will not budge. It's the bolt that holds the fuel filter in place so I have to use a wrench, no way to get a socket on there... It is actually beginning to strip so I don't wanna try to much... any advice will be helpful.
thanks =)How do I remove a stuck bolt on my fuel filter?Get a good penetrating oil and spray it on a few times a day for a few days.
That should help
WD-40 can be used for lots of things but it is not realy a penetrating oil.
It was made to displace waterHow do I remove a stuck bolt on my fuel filter?try a paIR OF VICE GRIPS ON IT or chain wrench
thanks =)How do I remove a stuck bolt on my fuel filter?Get a good penetrating oil and spray it on a few times a day for a few days.
That should help
WD-40 can be used for lots of things but it is not realy a penetrating oil.
It was made to displace waterHow do I remove a stuck bolt on my fuel filter?try a paIR OF VICE GRIPS ON IT or chain wrench
What is the purpose of a fuel filter? How much do they usually run cost-wise?
I realize that it %26quot;filters.%26quot; But what the heck does it filter. It's not like debris gets into your gas tank or if so, I haven't the slightest idea how. I have a Haynes Manual for my truck so I know how to replace it and how often--I just don't know what exactly their purpose is.What is the purpose of a fuel filter? How much do they usually run cost-wise?Actually, plenty gets into the gas tank. I've opened one from an older car, and it was filthy inside. You can get dirt, sand, anything that might get carried in by the wind while you're filling up, or even if the person before you dropped the hose on the ground. Plus, gas tanks can start to rust, and bits break off in the inside. Without the fuel filter, any of this stuff can clog up the tiny passageways in your carburetter or fuel injector(s) and cause a rather expensive repair. As for the cost, older cars with a carb generally have a small filter just inside the connection between the fuel line and the carb itself. These can be as cheap as $2-3. On fuel injected cars, and some others, will have one in the fuel line somewhere under the vehicle or inside the gas tank. These can run more, possibly $20 or more. However, it is still cheap insurance when you consider the possible alternative repair bills. Also, if the filter is one of the ones between the carb and the fuel line can usually be removed with a pair of wrenches, while the ones in the line or in the tank require more tools, and sometimes specific ones. Some of these, however, can be duplicated by commonly available tools and materials.What is the purpose of a fuel filter? How much do they usually run cost-wise?Like any other filter, it drains out impurities in your fuel (dirt, ludge, engine particles, etc) to give cleaner fuel for your car/engine to run on.
Thecost varies according to the car you have.What is the purpose of a fuel filter? How much do they usually run cost-wise?Nowadays, the fuel pump is located inside of the fuel tank and is usually electric. The pump creates positive pressure in the fuel lines, pushing the gasoline to the engine. The higher gasoline pressure raises the boiling point. Placing the pump in the tank puts the component least likely to handle gasoline vapor well (the pump itself) farthest from the engine, submersed in cool liquid. Another benefit to placing the pump inside the tank is that it is less likely to start a fire. Though electrical components (such as a fuel pump) can spark and ignite fuel vapors, liquid fuel will not explode (see explosive limit) and therefore submerging the pump in the tank is one of the safest places to put it. In most cars, the fuel pump delivers a constant flow of gasoline to the engine; fuel not used is returned to the tank. This further reduces the chance of the fuel boiling, since it is never kept close to the hot engine for too long.
The electric fuel pump is generally on whenever the car's ignition switch is in the %26quot;on%26quot; position. Depressing the gas pedal results in the throttle body opening on the engine (metering the air going in) rather than engaging the fuel pump. The ignition switch does not carry the power to the fuel pump, instead it activates a relay which will handle the higher current load. It is common for the fuel pump relay to become oxidized and cease functioning; this is much more common than the actual fuel pump failing.
Some cars with an electronic control unit have safety logic that will shut the electric fuel pump off even if the ignition is %26quot;on%26quot; if there is no oil pressure, either due to engine bearing damage or a non stalled engine, e.g. in a car accident. In case of an accident this will also prevent fuel leaking from any ruptured fuel line. Other cars have an additional roll over valve, that will shut off the fuel pump in case the car rolls over.What is the purpose of a fuel filter? How much do they usually run cost-wise?you have to remember your tank is not the only thing the gas sits in, and none of the containers including your tank are sterile. 1/100 of an ounce of dirt every tank can add up after 30,000 miles. The cost depends on what you drive, an old school inline filter off a dodge 225 slant six would be $1.99. Some fuel injected filters and diesel filters can run $100 or moreWhat is the purpose of a fuel filter? How much do they usually run cost-wise?fFOR MORE INFO GO TO:http://en.wikipedia.org/wiki/Fuel_filter
Found in most internal combustion engines, a fuel filter is a filter in the fuel line that screens out dirt and rust particles from the fuel. Fuel filters serve a vital function in today's modern, tight-tolerance engine fuel systems. Unfiltered fuel may contain several kinds of contamination, for example paint chips and dirt that has been knocked into the tank while filling, or rust caused by moisture in a steel tank. If these substances are not removed before the fuel enters the system, they will cause rapid wear and failure of the fuel pump and injectors, due to the abrasive action of the particles on the high-precision components used in modern injection systems. Fuel filters also improve performance, as the less contaminants in the fuel, the more efficiently it can be burnt.
Cost depends on what type of vehicle you have.What is the purpose of a fuel filter? How much do they usually run cost-wise?Although there are no impurities in petrol/gasoline sold at retail outlets, they still manage to get in to your fuel tank. When you're filling up, airborne dirt sneaks in and - especially in older vehicles with metal tanks, the lining of the tank begins to break down and small flecks of metal, rust and similar can make their way into the fuel line.
The filter will absorb this. On your new vehicle, you really shouldn't have to change them unless you live in a dusty climate. Even then, an aftermarket in-line fuel filter replacement will cost only a few dollars compared to the vehicle's brand name filter, which is often exactly the same.What is the purpose of a fuel filter? How much do they usually run cost-wise?Your fuel filter obviously filters,,,,,,, it filters out any contamination that might have gotten into your tank or the fuel itself, like dirt, sand or water. depending on the exact make and model of your vehicle the price could range any where from $1 to $20. but there not hard to replace yourselfWhat is the purpose of a fuel filter? How much do they usually run cost-wise?The fuel you get at the pump isn't always dirt and water free and the inside of metal gas tanks can also corrode. The filter keeps this stuff from getting into your engine.What is the purpose of a fuel filter? How much do they usually run cost-wise?You will indeed get crap in the fuel. I cut open a couple of filters with a hacksaw to see if there was any crud inside them and sure enough there was a considerable amount. If you have a fuel injected vehicle its critical to filter the gas as a small piece of crud can clog up your injectors. You can go to long without changing the filter and eventually your car will start sputtering as it is being starved for fuel do to the amount of crud in the filter. The fuel injected vehicles usually have the filter underneath the car and are in line with the fuel line. Your owners manual should tell you how often to change them. They should be good for at least 30,000 miles or more depending on the make of your vehicle.What is the purpose of a fuel filter? How much do they usually run cost-wise?You're right, it filters dust and rust and other fine debris which could block the fine nozzles in fuel injectors and carburetters. Contaminated fuel or careless filling of your petrol tank can introduce impurities and are the main causes for the need for a fuel filter.What is the purpose of a fuel filter? How much do they usually run cost-wise?Your filter, filters out impurities. Like water, dirty, sediment. Things that would damage your engine. Depending on the brand and the type your vehicle uses, they don't usually run that much.What is the purpose of a fuel filter? How much do they usually run cost-wise?Fuel is one of the sources for the most dirty and contamination entering your engine. Since fuel has to be atomized, it passes throught some very tiny places. Any piece of dirt or rust flakes can plug that up in a hurry. In addition, the abrasivness of the dirt in fuel will cause problems inside the engine.
A fuel filter must be changed because they rapidly get full of contamination and dirt.
Just watch the gas truck make a delivery to the gas station. The fuel from that dirty truck is pumped through a dirty hose into a tank in the ground through a hole in the concrete. More dirt gets into fuel than you might think. change that fuel filter.What is the purpose of a fuel filter? How much do they usually run cost-wise?Do you think that fuel is clean? It sits in a tank at the gas station that who knows when has it been cleaned!! You would be surprised at what kind of dirt is in a fuel filter that hasn't been changed! The purpose of a fuel filter is that it cleans most of the fuel before it reaches your injectors!!! It cost $20 to 30 dollars for a fuel filter compared to over a $1000 for new injectors that are damaged caused by dirty fuel !!!What are duvet covers best ergonomic mouse
Thecost varies according to the car you have.What is the purpose of a fuel filter? How much do they usually run cost-wise?Nowadays, the fuel pump is located inside of the fuel tank and is usually electric. The pump creates positive pressure in the fuel lines, pushing the gasoline to the engine. The higher gasoline pressure raises the boiling point. Placing the pump in the tank puts the component least likely to handle gasoline vapor well (the pump itself) farthest from the engine, submersed in cool liquid. Another benefit to placing the pump inside the tank is that it is less likely to start a fire. Though electrical components (such as a fuel pump) can spark and ignite fuel vapors, liquid fuel will not explode (see explosive limit) and therefore submerging the pump in the tank is one of the safest places to put it. In most cars, the fuel pump delivers a constant flow of gasoline to the engine; fuel not used is returned to the tank. This further reduces the chance of the fuel boiling, since it is never kept close to the hot engine for too long.
The electric fuel pump is generally on whenever the car's ignition switch is in the %26quot;on%26quot; position. Depressing the gas pedal results in the throttle body opening on the engine (metering the air going in) rather than engaging the fuel pump. The ignition switch does not carry the power to the fuel pump, instead it activates a relay which will handle the higher current load. It is common for the fuel pump relay to become oxidized and cease functioning; this is much more common than the actual fuel pump failing.
Some cars with an electronic control unit have safety logic that will shut the electric fuel pump off even if the ignition is %26quot;on%26quot; if there is no oil pressure, either due to engine bearing damage or a non stalled engine, e.g. in a car accident. In case of an accident this will also prevent fuel leaking from any ruptured fuel line. Other cars have an additional roll over valve, that will shut off the fuel pump in case the car rolls over.What is the purpose of a fuel filter? How much do they usually run cost-wise?you have to remember your tank is not the only thing the gas sits in, and none of the containers including your tank are sterile. 1/100 of an ounce of dirt every tank can add up after 30,000 miles. The cost depends on what you drive, an old school inline filter off a dodge 225 slant six would be $1.99. Some fuel injected filters and diesel filters can run $100 or moreWhat is the purpose of a fuel filter? How much do they usually run cost-wise?fFOR MORE INFO GO TO:http://en.wikipedia.org/wiki/Fuel_filter
Found in most internal combustion engines, a fuel filter is a filter in the fuel line that screens out dirt and rust particles from the fuel. Fuel filters serve a vital function in today's modern, tight-tolerance engine fuel systems. Unfiltered fuel may contain several kinds of contamination, for example paint chips and dirt that has been knocked into the tank while filling, or rust caused by moisture in a steel tank. If these substances are not removed before the fuel enters the system, they will cause rapid wear and failure of the fuel pump and injectors, due to the abrasive action of the particles on the high-precision components used in modern injection systems. Fuel filters also improve performance, as the less contaminants in the fuel, the more efficiently it can be burnt.
Cost depends on what type of vehicle you have.What is the purpose of a fuel filter? How much do they usually run cost-wise?Although there are no impurities in petrol/gasoline sold at retail outlets, they still manage to get in to your fuel tank. When you're filling up, airborne dirt sneaks in and - especially in older vehicles with metal tanks, the lining of the tank begins to break down and small flecks of metal, rust and similar can make their way into the fuel line.
The filter will absorb this. On your new vehicle, you really shouldn't have to change them unless you live in a dusty climate. Even then, an aftermarket in-line fuel filter replacement will cost only a few dollars compared to the vehicle's brand name filter, which is often exactly the same.What is the purpose of a fuel filter? How much do they usually run cost-wise?Your fuel filter obviously filters,,,,,,, it filters out any contamination that might have gotten into your tank or the fuel itself, like dirt, sand or water. depending on the exact make and model of your vehicle the price could range any where from $1 to $20. but there not hard to replace yourselfWhat is the purpose of a fuel filter? How much do they usually run cost-wise?The fuel you get at the pump isn't always dirt and water free and the inside of metal gas tanks can also corrode. The filter keeps this stuff from getting into your engine.What is the purpose of a fuel filter? How much do they usually run cost-wise?You will indeed get crap in the fuel. I cut open a couple of filters with a hacksaw to see if there was any crud inside them and sure enough there was a considerable amount. If you have a fuel injected vehicle its critical to filter the gas as a small piece of crud can clog up your injectors. You can go to long without changing the filter and eventually your car will start sputtering as it is being starved for fuel do to the amount of crud in the filter. The fuel injected vehicles usually have the filter underneath the car and are in line with the fuel line. Your owners manual should tell you how often to change them. They should be good for at least 30,000 miles or more depending on the make of your vehicle.What is the purpose of a fuel filter? How much do they usually run cost-wise?You're right, it filters dust and rust and other fine debris which could block the fine nozzles in fuel injectors and carburetters. Contaminated fuel or careless filling of your petrol tank can introduce impurities and are the main causes for the need for a fuel filter.What is the purpose of a fuel filter? How much do they usually run cost-wise?Your filter, filters out impurities. Like water, dirty, sediment. Things that would damage your engine. Depending on the brand and the type your vehicle uses, they don't usually run that much.What is the purpose of a fuel filter? How much do they usually run cost-wise?Fuel is one of the sources for the most dirty and contamination entering your engine. Since fuel has to be atomized, it passes throught some very tiny places. Any piece of dirt or rust flakes can plug that up in a hurry. In addition, the abrasivness of the dirt in fuel will cause problems inside the engine.
A fuel filter must be changed because they rapidly get full of contamination and dirt.
Just watch the gas truck make a delivery to the gas station. The fuel from that dirty truck is pumped through a dirty hose into a tank in the ground through a hole in the concrete. More dirt gets into fuel than you might think. change that fuel filter.What is the purpose of a fuel filter? How much do they usually run cost-wise?Do you think that fuel is clean? It sits in a tank at the gas station that who knows when has it been cleaned!! You would be surprised at what kind of dirt is in a fuel filter that hasn't been changed! The purpose of a fuel filter is that it cleans most of the fuel before it reaches your injectors!!! It cost $20 to 30 dollars for a fuel filter compared to over a $1000 for new injectors that are damaged caused by dirty fuel !!!
How do I remove a fuel Filter for a Ford?
I Have a 2001 Ford Explorer Sport 2 Door 4.0 LT I got the tool to disconnect the lines for the fuel filter but i still cant remove it. what the hell am I doing wrong ? I am old school. Can any body help?How do I remove a fuel Filter for a Ford?you gotta get mean with that connection/down rite angry and mean/no other way/cuss at it toHow do I remove a fuel Filter for a Ford?first step, slide the tool onto the filter, push tool towards the line while pushing the filter and the line together, after you push the filter and line together push the tool more into the line fitting, then twist and pull the filter out while still pushing the tool into the line fittingHow do I remove a fuel Filter for a Ford?Aren't they mean? Just push the tool in and they should release. Try turning it in the bore. I hate them too. Split the connection and take out each half sometimes works. Good luckHow do I remove a fuel Filter for a Ford?Have you relieved the pressure from the system? If not, that could make it more difficult to get the clips to release and if it does come loose it'll spray fuel everywhere, so make sure you do that first. Slide the tool over the clips as described in the instructions. You may have to push or pull the filter a little to get the clip to release, but it shouldn't be hard. Make sure there's no dirt in the clips, that'll make it harder also.
How do I change a fuel filter on a 2000 Ford Windstar LX?
I am looking for step by step instructions; do I need to shut the fuel off somehow first? Will fuel spray out at me? Should I do it on an empty gas tank?How do I change a fuel filter on a 2000 Ford Windstar LX?the fuel filter should be under the right side (when you sit in the driver seat). You will see two metal tubes go into a larger metal tube. The large one is your fuel filter. Get two line wrenches to fit the two nuts and loosen the nuts. Put a bucket under it because there is going to be residual fuel in the line when you disconect it. Take out the old one and tighten the new one in. Replace any brackets that held the old filter in. It may take a second for your car to start afterwards because the lines need to be primed again. Hope that helps.How do I change a fuel filter on a 2000 Ford Windstar LX?aHow do I change a fuel filter on a 2000 Ford Windstar LX?Its a ford dont bother!!How do I change a fuel filter on a 2000 Ford Windstar LX?there is a fuse in the fuse panel... pull the fuse out for the fuel pump relay and then start the engine... let it run until it dies on it's own to take the pressure out of the lines... the fuel filter should be located on the drivers side between the back of the drivers door and the rear tire.... undo the strap holding the filter in place... ford has a %26quot;quick disconnect%26quot; fitting on their filters that take a special tool that can be bought at most parts stores - don't worry they aren't very expensive... that tool fits around the fuel line and slides into the end of the filter sometimes you have to press it in pretty firmly... this will release the lock that keeps the line from falling out... and then gently pull on the fuel line... if it hasn't been changed in several years it can be a real pain in the butt to get to release... do the other side the same way and then push the ends of the fuel line on to the new filter and reattach the strap around the filter... re-install the fuse and turn the key to the on position.... be sure to check for leaks.... hope this helps and good luck with itHow do I change a fuel filter on a 2000 Ford Windstar LX?FORD FUEL FILTER REQUIRE A SPECIAL TOOL TO REMOVE THE PLASTIC LOCKS AT EACH END OF THE FILTER. OTHERWISE YOU CAN DAMAGE THEM. THEY ARE THE ONLY THING THAT HOLD IT TOGETHER SO THERE NO LEAK.
JACK UP THE VEHICLE AND USE SAFETY STANDS. TAKE SPECIAL TOOL AND DEPRESS THE LOCK. THERE WILL A SMALL AMOUNT OF GAS COMING OUT. IT IS THE PRES SUE IN THE FUEL LINE. SO NO SMOKING IN THE AREA. THE OTHER END COME A PART THE SAME WAY. TO INSTALL THE NEW FILTER. PRESS THE LINE INTO THE FILTER. yOU SHOULD HEAR A CLICK. tEST BY TRYING TO PUT THE OUT OF THE FILTER. tHE OTHER END GO THE SAME WAY. IT IS INSTALLED. THIS IMPORTANT! tURN THE KEY ON FIVE OR SIX TIMES. tHIS BUILD THE PRESSURE UP IN THE FUEL LINE. tHEN START THE VEHICLE AND CHECK FOR LEAKS AT THE FILTER. IF THERE LEAKS THEN CUT THE ENGINE OFF. THE LINES IS NOT ALL THE WAY IN THE FILTER. AND REPEAT THE START UP. tHERE SHOULD BE NO LEAKS AT ALL.
JACK UP THE VEHICLE AND USE SAFETY STANDS. TAKE SPECIAL TOOL AND DEPRESS THE LOCK. THERE WILL A SMALL AMOUNT OF GAS COMING OUT. IT IS THE PRES SUE IN THE FUEL LINE. SO NO SMOKING IN THE AREA. THE OTHER END COME A PART THE SAME WAY. TO INSTALL THE NEW FILTER. PRESS THE LINE INTO THE FILTER. yOU SHOULD HEAR A CLICK. tEST BY TRYING TO PUT THE OUT OF THE FILTER. tHE OTHER END GO THE SAME WAY. IT IS INSTALLED. THIS IMPORTANT! tURN THE KEY ON FIVE OR SIX TIMES. tHIS BUILD THE PRESSURE UP IN THE FUEL LINE. tHEN START THE VEHICLE AND CHECK FOR LEAKS AT THE FILTER. IF THERE LEAKS THEN CUT THE ENGINE OFF. THE LINES IS NOT ALL THE WAY IN THE FILTER. AND REPEAT THE START UP. tHERE SHOULD BE NO LEAKS AT ALL.
Does anyone know how to change a fuel filter in a 1993 Isuzu bighorn?
Need to know how to bleed the diesel system once i have changed the filter.Does anyone know how to change a fuel filter in a 1993 Isuzu bighorn?Ive never had to %26quot;bleed%26quot; the fuel system. some of them actually have a manual pump for this occasion, while others you just have to be patient and just keep cranking the engine over until it starts.
Subscribe to:
Posts
(Atom)